Hardware Manuals


Mixvibes - VFX Control - Layout  

EFFECT CONTROLS


The Effects section of the VFX CONTROL offers 3 different modes. Single Audio FX, Multi Audio FX and Video FX modes. These modes are selected via the FX/MODE button.

  1. FX/MODE:Use this button to toggle between the Audio and Video mode for the FX section.
    When in Audio FX mode, hold SHIFT down and then use this button to toggle between Single and Multi Audio FX modes.

  2. FX LED BAR:The 8 sequential Leds will indicate the status of the Audio or Video Effects, depending on the selected mode, as explained further in this chapter.


Audio Single FX mode


  1. FX ENC 1: Turn this encoder to select an Audio Effect.
    Push the encoder to enable/disable the selected Effect to Left/Right Deck. Hold SHIFT and then push the encoder to open/close the Effect's GUI at the side of the Browser and view all of its Parameters.
    The 1st LED from left will blink if the Effect is enabled and solid if not.

  2. FX ENC 2: Turn this encoder to adjust the 1st Parameter of the selected Effect. Hold SHIFT down and then use the same encoder to adjust its 3rd Parameter.
    Push the encoder to enable/disable the 1st Parameter button of the selected Effect. Hold SHIFT and then push the encoder to enable/disable the 3rd Parameter button of the selected Effect (if available)
    The 2nd LED from left will be turned off in this mode

  3. FX ENC 3: Turn this encoder to adjust the 2ndParameter of the selected Effect. Hold SHIFT down and then use the same encoder to adjust its 4thParameter.
    Push the encoder to enable/disable the 2ndParameter button of the selected Effect. Hold SHIFT and then push the encoder to enable/disable the 4th Parameter button of the selected Effect (if available)
    The 3rd LED from left will be turned off in this mode


Audio Multi FX mode


  1. FX ENC 1: Turn this encoder to adjust the 1st Parameter of the selected Effect of the FX Slot 1. Hold SHIFT down and then use this encoder to adjust the 2nd Parameter of the selected Effect in FX Slot 1
    Push the encoder to enable/disable the selected Effect in FX Slot 1.. Hold SHIFT down and then push the encoder to select the next available Effect for FX Slot 1
    The 1st LED from left will blink if the Effect in FX Slot 1 is enabled and solid if not.

  2. FX ENC 2: Turn this encoder to adjust the 1st Parameter of the selected Effect of the FX Slot 2. Hold SHIFT down and then use this encoder to adjust the 2nd Parameter of the selected Effect in FX Slot 2
    Push the encoder to enable/disable the selected Effect in FX Slot 2.. Hold SHIFT down and then push the encoder to select the next available Effect for FX Slot 2
    The 2nd LED from left will blink if the Effect in FX Slot 2 is enabled and solid if not.

  3. FX ENC 3: Turn this encoder to adjust the 1st Parameter of the selected Effect of the FX Slot 3. Hold SHIFT down and then use this encoder to adjust the 2nd Parameter of the selected Effect in FX Slot 3
    Push the encoder to enable/disable the selected Effect in FX Slot 3.. Hold SHIFT down and then push the encoder to select the next available Effect for FX Slot 3
    The 3rd LED from left will blink if the Effect in FX Slot 3 is enabled and solid if not.




Video FX mode


  1. FX ENC 1: Turn this encoder to apply a High/Low-Pass Filter to the left/right deck. Push to reset and turn off Filter.
    The 4th LED from left, will blink if Filter is applied and solid if not.

  2. FX ENC 2: Turn this encoder to adjust the Key of the track. Push this encoder to reset the Key of the track to its original value. Hold SHIFT and then push the encoder to match the key of the deck with the opposite deck's value.
    The 5th LED from left will blink if the current Key of the deck is different than its original.

  3. FX ENC 3 LEFT: Turn the left-side encoder to select a Video Transition. Push the left-side encoder to manually trigger the selected video transition.
    Hold SHIFT and then use the left-side encoder to adjust the 1st Parameter of the selected Video Transition (if available). Hold SHIFT down and then push the left-side encoder to open/close its GUI at the side of the Browser and see all of its available Parameters (if any)
    The 6th left-side LED from left will blink if a Video Transition is performed

    FX ENC 3 RIGHT: Turn the right-side encoder to select a Video Effect for the Master Video Output. Push the right-side encoder to manually trigger the selected Video Effect.
    Hold SHIFT and then use the right-side encoder to adjust the 1st Parameter of the selected Video Effect (if available). Hold SHIFT down and then push the right-side encoder to open/close its GUI at the side of the Browser and see all of its available Parameters (if any)
    The 6th right-side LED from left will blink if a Video Effect is enabled


Rear panel